sjx 2170 jet boat

The sjx 2170 is your 4-wheel drive on the water

The SJX 2170 Jet Boat is our most poplar model. It provides the nimbleness of a smaller light-weight boat with the versatility of a cargo boat due to it's hauling capabilities. The SJX 2170 is the jet boat that will get you where you what to go. No question!

aluminum Hull

5052-H32 Alloy Temper used for most construction except where specified. All floors and deck hatch lids coated with bed-liner material also with sound deadening insulation. Zero Alum to Alum contact between boat subfloor and flooring! Triple bulkhead cross floor construction, 28 cross floor braces @ 16 inch centers, .125 (1/8 inch) thick channels 6063-T6 Alloy Temper, bulkhead plates .166 (3/16 inch) thickness.

  • 21 ft. Boat, 70 inch bottom width, 1/8 inch bottom thickness
  • 27 inch sides, 1/8 inch thickness
  • Transom thickness of .160 (between 3/16" and 1/8")
  • Intake and Tunnel thickness of.250 (1/4 inch)
  • Aluminum Floors and all deck surfaces are .125 (1/8 inch)
  • Center Hull Stiffener "C" Channel full length 6063-T6 Alloy
  • "box runners" are .125 (1/8 inch) full length
  • 6 full length standard hull stiffeners ( 2" channels), 6063-T6 Alloy .

ZERO SKIP WELDING ON ALL FORWARD TO AFT HULL STIFFENERS & BOX RUNNERS. FULL LENGTH CONTINUOUS WELDS!!! (Or CONTINUOUS FULL LENGTH WELDS!!!

ENGINE & JET DRIVE

Engine; Mercury 200 hp Optimax™ DFI Sport Jet package.

Marine XHD Deep Cycle Interstate™ battery.

3 gallon, 2-cycle oil tank reservoir, with low oil sensor.

Racor fuel water separator with 1/4 turn shut-off valve*

40 gallon aluminum fuel tank**

Whisper external mufflers, 100% isolated from metal to metal contact to prevent excessive noise and vibrations.

Jet Drive; Mercury SJ M2 JD with stainless steel "Hi-Skew" impeller.

Reverse gate extensions for additional reverse thrusting abilities***

Stainless Steel 9 bar EZ-Clean Jet Intake Cleanout System

* Mercury Sport Jet engines are equipped with a additional on-board fuel water separator "dual protection").

**NEW 2013 EPA approved closed fuel system, dual anti-siphon ventilation, and splash tray fill.

***Reverse gate modifications, extensions are another SJX exclusive extrusion for additional reverse thrusting abilities, 6063-T6 Alloy Temper.

INSTRUMENTATION, CONTROLS, & HARDWARE

Custom "SJX" instrument and switch panel.

Complete  "Smart-Craft" multi function Instrument Package.

Additional Fuel Gauge Instrument linked to Smart-Craft™ System.

All applicable deck hardware.

Complete Dual T-500 GPH Bilge system *

4 inch Blower and stainless cowl vent system**

Single levers control shifter/throttle combo with neutral safety switch

Lanyard tether kill switch.

*All Mercury Sport Jet engines are equipped with a additional on-board "Siphon Bilge" system, if there is water in your bilge and the motor is running it also is siphoning the water out.
**NEW - 4 inch Blower and stainless cowl vent system to accommodate NEW USCG ventilation regulations and standards.

CONSOLE ASSEMBLY

Dual Console assembly, 3 piece windshield with center walk-thru, upper and lower console doors for easy access, passenger side glove compartment passenger side, storage step box, .125 (1/8 inch) thickness, 5052-H32 Alloy Temper, solid bulkhead type construction yet still removable "Zero Flex".

DECKs & SEAT BOXES

Raised rear deck over fuel tank, storage compartments on sides of engine compartment.

Step-up front deck.

Interior 4-wheelers ramps.

Large bow hatch with hinging lockable lid with storage.

Aluminum seat/storage boxes, hinging lid, with custom folding and swiveling seats (color choices).

PAINT and COATINGS

Entire "Exterior" painted with color choices, and standard graphics. All paint and primer is top of the line PPG products

Entire "Interior" bed-liner coating with color choices. A nice feature about our bed-liners is you can purchase one of our bed liner kits and do a repair at your home or shop.

EXCLUSIVE EXTRUSIONS

sjx-2170-jet-boat-extrusions-sjx-jet-boats

  • Outer 1 1/2 inch Handrail/gunwale, 6063-T6 Alloy Temper.
  • Inner 1 inch Handrail, 6063-T6 Alloy Temper.
  • Center Hull Stiffener "C" Channel.
  • Outer Receiver Hitch Socket 2 inch square tubing, .250 (1/4 inch) thickness, 6063-T6 Alloy Temper.
  • Inner Receiver Hitch Socket Insert square tubing, .500 (1/2 inch) wall thickness, 6063-T6 Alloy Temper.
  • Reverse Gate Extension Tubing, .166 (3/16 inch) wall thickness, 6063-T6 Alloy Temper.
  • Heater line tubing, 3/4 inch OD, .125 (1/8 inch) wall thickness, 6063-T6 Alloy Temper.
  • Deck Hatch Framing Channel, .125 (1/8 inch) thickness, 6063-T6 Alloy Temper.

 

ADDITIONAL ITEMS
  • Welded transom eyes, 3/8 inch thickness, 6063-T6 Alloy Temper.
  • Welded bow eye, 3/8 inch thickness, 6063-T6 Alloy Temper.
  • Weld-on transducer brackets for fish and depth finders.
  • Weld-on zinc plate brackets.
  • Swim deck/Jet guard.
  • Entire "Interior" bed-liner coating with color choices.